Cembrit Cover

Intense colours for expressive facades

The natural grey fibre cement base board is finished with a water based acrylic surface coating. The standard range incorporates 26 colours with the option (based on quantity and lead time) of made to order colours in any one of 2000 NCS®© shades. Like all Cembrit fibre cement claddings Cembrit Cover is an A rated board.

Cembrit Cover

Colours & Measures

Cembrit Cover

Selected colour: C 010

Free sample: C 010

C 010
C 020
C 040
C 050
C 060
C 160
C 190
C 200
C 210
C 350
C 360
C 370
C 390
C 450
C 530
C 540
C 550
C 570
C 610
C 630
C 640
C 650
C 670
C 730
C 760
C 770

Special colours available

Choose from 1900 NCS options to suit your induvidual design - dependent on quantity and lead time.

Colour
Thickness
Width
Length
C 010
8 mm
1192 mm
3040 mm
C 010
8 mm
1250 mm
3050 mm
C 010
8 mm
1250 mm
2500 mm
C 020
8 mm
1192 mm
2500 mm
C 020
8 mm
1250 mm
2500 mm
C 020
8 mm
1250 mm
3050 mm
C 040
8 mm
1250 mm
2500 mm
C 040
8 mm
1250 mm
3050 mm
C 050
8 mm
1192 mm
2500 mm
C 050
8 mm
1270 mm
3070 mm
C 050
8 mm
1250 mm
2500 mm
C 050
8 mm
1250 mm
3050 mm
C 060
8 mm
1192 mm
2500 mm
C 060
8 mm
1270 mm
3070 mm
C 060
8 mm
1250 mm
2500 mm
C 060
8 mm
1250 mm
3050 mm
C 160
8 mm
1192 mm
2500 mm
C 160
8 mm
1270 mm
3070 mm
C 160
8 mm
1250 mm
2500 mm
C 160
8 mm
1250 mm
3050 mm
C 210
8 mm
1192 mm
2500 mm
C 210
8 mm
1270 mm
3070 mm
C 210
8 mm
1250 mm
2500 mm
C 210
8 mm
1250 mm
3050 mm
C 360
8 mm
1192 mm
2500 mm
C 360
8 mm
1270 mm
3070 mm
C 360
8 mm
1250 mm
2500 mm
C 360
8 mm
1250 mm
3050 mm
C 390
8 mm
1192 mm
2500 mm
C 390
8 mm
1270 mm
3070 mm
C 390
8 mm
1250 mm
2500 mm
C 390
8 mm
1250 mm
3050 mm
C 450
8 mm
1192 mm
3040 mm
C 450
8 mm
1250 mm
2500 mm
C 450
8 mm
1250 mm
3050 mm
C 530
8 mm
1250 mm
2500 mm
C 530
8 mm
1250 mm
3050 mm
C 540
8 mm
1192 mm
2500 mm
C 540
8 mm
1270 mm
3070 mm
C 540
8 mm
1250 mm
2500 mm
C 540
8 mm
1250 mm
3050 mm
C 550
8 mm
1250 mm
2500 mm
C 550
8 mm
1250 mm
3050 mm
C 550
8 mm
1270 mm
2530 mm
C 550
8 mm
1270 mm
3070 mm
C 570
8 mm
1250 mm
2500 mm
C 570
8 mm
1250 mm
3050 mm
C 570
8 mm
1192 mm
2500 mm
C 570
8 mm
1192 mm
3050 mm
C 610
8 mm
1250 mm
2500 mm
C 610
8 mm
1250 mm
3050 mm
C 630
8 mm
1270 mm
2530 mm
C 630
8 mm
1270 mm
3070 mm
C 630
8 mm
1250 mm
2500 mm
C 630
8 mm
1250 mm
3050 mm
C 640
8 mm
1250 mm
2500 mm
C 640
8 mm
1250 mm
3050 mm
C 650
8 mm
1250 mm
2500 mm
C 650
8 mm
1250 mm
3050 mm
C 670
8 mm
1250 mm
2500 mm
C 670
8 mm
1250 mm
3050 mm
C 730
8 mm
1250 mm
2500 mm
C 730
8 mm
1250 mm
3050 mm
C 760
8 mm
1250 mm
2500 mm
C 760
8 mm
1250 mm
3050 mm
C 760
8 mm
1270 mm
2530 mm
C 760
8 mm
1270 mm
3070 mm
C 770
8 mm
1250 mm
2500 mm
C 770
8 mm
1250 mm
3050 mm

Cembrit Cover

It is life lived in colour.

Cembrit Cover is all about appearance and creating long-lasting first impressions. This is the board you would bring along to a red-carpet event: Flashy, but never too much. Expressive, but with something important to say.

With endless colour variations, Cembrit Cover allows you to explore and pursue any architectural idea and becomes a constant source of vibrant energy. It is thus perfect for buildings that house learning, laughter and life.

Blend in or stand out? With Cembrit Cover, you decide.

 

Cembrit Cover is the ideal solution if you prefer the strongest colours and bolder design statements. The natural grey fibre-cement core is completely covered by a layer of water-based acrylic paint, with 26 standard Cembrit colours and more than 2000 NCS®© colours to choose from.

Product features:
NON COMBUSTIBLE
DURABLE
MAINTENANCE FREE
MOULD RESISTANT
IMPACT RESISTANT
SUSTAINABLE
WIDE COLOUR RANGE

Technical data

Material

Fibre cement

Coating and surface

Water-based acrylic paint.

Type

Non-Through coloured

Colours

26

Fire protection Class

A2 - s1, d0

Fixing - aluminium

For aluminium substructure use Cembrit Rivets Aluminium 4.0x20mm. Make sure to use Cembrit Nose tool together with the rivet gun to get the correct tightening of the rivet.

Fixing - steel

For steel substructure use Cembrit Rivets steel 4.8x20mm or a Cembrit Facade screw CL-SS 4.8x29. A washer is pre-mounted on the screw to ensure the screw is centered and the hole is closed. Make sure to use Cembrit Nose tool together with the rivet gun to get the correct tightening of the rivet.

Fixing - wood

Cembrit Facade Screw is available as unpainted or in colours corresponding to the facade boards and in two steel qualities, A2 and A4. A washer is pre-mounted on the screw to ensure the screw is centered and the hole is closed.

References

Cembrit Cover

Selected colour: C 010

Installation

Cembrit Cover

Aluminium Installation

Aluminium support system Mounting 8mm Cembrit facade boards on aluminium Max. support distances: 629mm o.c. Max. rivet centres: 600mm Max wind load: Please refer to the wind load table for the correct distances for substructure and rivets. The following rivet types can be used for this construction: Cembrit Rivets Aluminium RIV-A 4.0x20mm  

Aluminium L Profile Detail

Cembrit facade boards can also be installed on horizontal aluminium systems. When using a horizontal support system, there must be a minimum of 20mm ventilated vertical area between the profiles and the supporting wall or insulation. 

Aluminium T Profile Joint

Edge Distances There should be a minimum of 20mm from the reverse of the facade board to the front face of the insulation to provide adequate ventilation. T profiles behind joints should be min 100mm width, and the L profiles should be min 40mm width. Joint gaps between boards should be min 8mm and max 16mm. The use of flat EPDM on aluminium profiles is optional, but from an aesthetic point of view, it may be advantageous to use it as the aluminium profiles will otherwise be visible through the joints. Alternatively, you can use black UV tape or painted aluminium profiles. 

Wood Installation

Installing 8mm Cembrit facade boards on timber frame Max support distances: 629mm o.c Max screw centres: 600mm o.c Max wind load: Please refer to the wind load table for the correct distances for substructure and screws. The following screws can be used for this solution: Cembrit Facade Wing Screw Wood, SCR-WW 4.9x38mm Cembrit Facade Screw Wood, SCR-W 4.5x30/36/41mm

Timber Screw Center

Cembrit recommends using an EPDM of the same width as the selected batten. Cembrit facade boards can also be installed on horizontal battens. When using horizontal substructures, there must be a minimum 20mm ventilated area behind the horizontal supporting battens. 

Timber Screw Joint

Battens should be a minimum of 20mm thickness to provide adequate ventilation. Batten width should be minimum 100mm for supporting battens, and 45mm for central battens. Joint gaps between boards should be a minimum of 8mm and a maximum of 16mm. When using timber battens, always use Cembrit EPDM with profiled ribs.  

Steel Installation

To ensure the optimum, long term performance and aesthetic characteristics for Cembrit facade boards it is vital to ensure that the support system substructure is absolutely straight, horizontally and vertically. In order to ensure this, please follow the guidelines below. Straightness of substructure The horizontal tolerance is +/- 3.0mm measured over a distance of 2 meters The vertical tolerance is +/- 0.5mm over 600mm measured over a distance of 2 meters.

Top Hat Center

Edge Distances There should be a minimum of 20mm from the reverse of the facade board to the front face of the Windstopper or insulation to provide adequate ventilation. The profiles behind joints should be min 100mm width, and the middle profiles should be min 40mm width. Joint gaps between boards should be min 8mm and max 16mm. Always use flat EPTL/EPDM on steel profiles as it will provide adequate protection of the boards from moisture movements. From an aesthetic point of view, including the EPTL/EPDM will also make the steel profiles less visible through the joints.

Top Hat Joint

Cembrit facade boards can also be installed on horizontal steel profile systems. When using a horizontal Cembrit VFL profile, the profiles can be mounted directly on the wall since it is perforated and the air can move freely. If using other horizontal systems, a minimum of 20mm ventilated vertical area between the profiles and the supporting wall or insulation must be ensured.